高溫鎮江NSK軸承的使用壽命與制造、安裝和使用密切相關。只有做好各環節的工作，才能使軸承處于良好工作狀態，從而延長軸承的使用壽命。

The service life of high temperature Zhenjiang NSK bearings is closely related to manufacture, installation and use. only by doing a good job in all links can the bearing be in good working condition, thus prolonging the service life of the bearing.

防止異物的安裝：在轉子動平衡軸承中，鐵的動平衡非常簡單，所以以前安裝動平衡軸承。為了便于安裝，一些制造商通過在軸承腔中添加一些油或潤滑脂來達到平滑的效果，但是操作人員常常難以控制油或潤滑脂的數量，如果更多的油或潤滑脂積聚在軸承腔中，則滾動軸承。軸是非常簡單的進入高溫鎮江NSK軸承的內部部分。不要在軸承腔內涂抹潤滑脂或油脂。如有必要，不要在軸承腔中積聚。

Prevent the installation of foreign bodies: In rotor dynamic balancing bearings, the dynamic balance of iron is very simple, so before the installation of dynamic balancing bearings. To facilitate installation, some manufacturers add some oil or grease to the bearing cavity to achieve a smooth effect, but operators often have difficulty controlling the amount of oil or grease, if more oil or grease accumulates in the bearing cavity, then the rolling bearing. The shaft is very simple to enter the internal part of the high temperature Zhenjiang NSK bearing. Do not apply grease or grease in the bearing cavity. If necessary, do not accumulate in the bearing cavity.

防止油漆腐蝕：密封電機經常被油漆腐蝕。電機在安裝過程中聲音非常好，但經過一段時間后，在倉庫中，電機的異常聲音變得非常大，當軸承、軸承嚴重銹蝕時。許多制造商習慣于認為軸承是一個問題，我們繼續汽車制造商已經認識到主要問題是絕緣涂料。這一問題主要是由于一定的溫濕度、絕緣漆酸蒸發、形成腐蝕性物質、腐蝕和高溫鎮江NSK軸承滾道損壞造成的。目前，只能選用好的絕緣清漆，干燥后還要安裝一段時間。

Prevent paint corrosion: seal motor is often corroded by paint. The sound of the motor is very good during the installation, but after a period of time, the abnormal sound of the motor becomes very large in the warehouse, when the bearings and bearings are seriously corroded. Many manufacturers are used to thinking of bearings as a problem, and we continue to recognize that the main problem is insulation paint. This problem is mainly due to certain temperature and humidity, insulation acid evaporation, the formation of corrosive substances, corrosion and high temperature Zhenjiang NSK bearing raceway damage caused. At present, only good insulating varnish can be selected, and it will be installed for some time after drying.

控制軸選擇和軸承室服務：滾動軸承壓入軸承時應敏銳，不堵塞。如果存在明顯的滾動不靈敏性和軸尺寸過大，則應減少維護。如果軸承被壓入軸內，滾動時，會有明顯的“沙子”感，可能過大或軸的圓度不好。因此，軸承室的軸控制和公共服務也應該取得很好的控制。目前，國內許多廠家只控制公共服務，而不是圓度。

Control shaft selection and bearing room service: when rolling bearings are pressed into bearings, they should be sharp and not clogged. If there is obvious rolling insensitivity and shaft size is too large, then maintenance should be reduced. If the bearing is pressed into the shaft, rolling, there will be obvious "sand" feeling, may be too large or shaft roundness is not good. Therefore, the shaft control and public service of the bearing chamber should also be well controlled. At present, many domestic manufacturers only control public services, not roundness.

軸承安裝：因為鎮江NSK軸承是高精度產品，如軸承安裝不當很容易損壞，導致高溫軸承損壞。軸承安裝時應采用特殊模具，不能引爆，當壓縮軸只有小環時，根據環量大。安裝過程中需要壓力或液壓。按壓時，上下感覺應在水平外。如果有一個歪斜，軸承滾道將損壞的力量和軸承將被引導。

Bearing Installation: Because Zhenjiang NSK bearings are high-precision products, such as improper bearing installation is easy to damage, resulting in high-temperature bearing damage. Bearings should be installed with special molds, can not be detonated, when the compression shaft only small ring, according to the large number of rings. Pressure or hydraulic pressure is required during installation. When pressing, the feeling of up and down should be outside the level. If there is a skew, the bearing raceway will damage the force and the bearing will be guided.

文章來自：鎮江SKF軸承 www.wh-skf.com

The article is from: Zhenjiang SKF bearing www.wh-skf.com

文章來自：鎮江INA軸承 www.ina-china.cn

The article is from: Zhenjiang INA bearing www.ina-china.cn

文章來自：鎮江NSK軸承 www.klbbearings.com

The article is from: Zhenjiang NSK bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672