相對于淮安SKF軸承座的注射點，有一個可與黃油嘴連接的絲錐。潤滑劑通過外圈直接接觸輥表面。管道柔軟，使用正常。zui好將潤滑脂注入旋轉中。

Compared with the injection point of Huaian SKF bearing seat, there is a tap which can be connected with butter nozzle. The lubricant contacts the surface of the roll directly through the outer ring. The pipeline is soft and normal to use. Zui is good at injecting grease into rotation.

油潤滑通常需要油潤滑來定位軸方向高溫、高速或過載的軸承。密封膠，100-400系列對向軸承可使用多種密封膠。

Oil lubrication usually requires oil lubrication to locate bearings with high temperature, high speed or overload in the axis direction. Sealant, 100-400 series of opposite bearings can use a variety of sealants.

實心球面軸承通常與剖分式sn和sd軸系結合使用。軸臺是可分離的，所以很容易裝配，但安裝和拆卸實心軸承很困難，這需要大量的時間。球面軸承可以用SPL系列的對向軸承代替，這種淮安SKF軸承可以安裝在現有的車軸上，而無需修改。

Solid spherical bearings are usually used in combination with split Sn and SD shafting. Shaft table is separable, so it is easy to assemble, but it is difficult to install and disassemble solid bearings, which takes a lot of time. Spherical bearings can be replaced by SPL series of opposite bearings. The Huaian SKF bearings can be installed on existing axles without modification.

1：首先，看看軸承鋼所用的材料。德國軸承由自己的專ye煉鋼廠生產。它們比假冒軸承具有更高的硬度和精度。

1: First, look at the materials used in bearing steel. German bearings are produced by its own Ye steelmaking plant. They have higher hardness and accuracy than counterfeit bearings.

2：為了樹立企業的品牌形象，防止假冒產品，軸承廠家采用激光打標機。他們希望利用高投入控制假冒產品，同時樹立自己的企業形象，達到國際標準。然而，由于激光打標是由計算機控制的，打印字體和尺寸的優點很容易編輯。它不僅能you效的標記。防止造假，但增加造假者的難度。

2: In order to establish the brand image of enterprises and prevent counterfeit products, bearing manufacturers adopt laser marking machine. They hope to use high investment to control counterfeit products, and at the same time establish their own corporate image, to meet international standards. However, because laser marking is controlled by computer, the advantages of printing fonts and sizes are easy to edit. It's not just a marker that works for you. Prevent counterfeiting, but increase the difficulty of counterfeiters.

3：觀察。用肉眼觀察滾動淮安SKF軸承，內外滾道應無剝落痕跡和嚴重磨損，呈弧形凹槽；所有滾動表面應wu斑灬、裂紋和剝落現象；保持架不應松動、損壞和磨損，與滾動體不應有大間隙。

3: Observation. The inner and outer raceways of rolling Huaian SKF bearings should be free of flaking marks and severe wear and tear, with arc grooves; all rolling surfaces should be Wu spots, cracks and flaking; cages should not be loosened, damaged and worn, and there should be no large gap with the rolling body.

4：手感法。內外座環與普通軸承滾子之間的間隙為0.005-0.010 mm。對于已經使用一段時間的滾動軸承，當內環通過夾指軸向擺動時，不應有明顯的野蠻聲音。

4: Handfeel method. The clearance between inner and outer seat rings and common bearing rollers is 0.005-0.010 mm. For rolling bearings that have been in use for some time, when the inner ring swings axially through the clamp finger, there should be no obvious barbaric sound.

5：旋轉法。一只手握住軸承內圈，另一只手轉動外圈。軸承轉動靈活，無徑向晃動。

5: Rotation method. One hand holds the inner ring of the bearing and the other hand rotates the outer ring. The bearing rotates flexibly without radial sloshing.

6：當然，這要看價ge。如果價ge比正常價ge低很多，這可能是一個錯誤的建議不買。畢竟，一分錢一分錢很貴，所以進口很貴。

6: Of course, it depends on the price ge. If the price Ge is much lower than the normal price ge, this may be a wrong suggestion not to buy. After all, a penny a penny is expensive, so imports are expensive.

檢查時，應結合以上五種經驗方法，正確判斷滾動軸承的技術狀態。對于圓錐滾子淮安SKF軸承，還需要觀察滾動元件是否位于外座圈的中間。如果向前移動，不應超過1.5 mm。

When inspecting, the technical status of rolling bearings should be correctly judged by combining the above five empirical methods. For tapered roller Huaian SKF bearings, it is also necessary to observe whether the rolling element is located in the middle of the outer seat ring. If moving forward, it should not exceed 1.5 mm.

文章來自：淮安SKF軸承 www.wh-skf.com

Article from: Huaian SKF Bearing www.wh-skf.com

文章來自：淮安INA軸承 www.ina-china.cn

Article from: Huaian INA Bearing www.ina-China.cn

文章來自：淮安NSK軸承 www.klbbearings.com

Article from: Huaian NSK Bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757