恒旺廠家供應 螺旋鉆機 輪式履帶式 速度快口徑大 樁工機械

螺旋鉆機采用加壓鉆進工作模式，可實現旋挖樁深2.5米、5.5米、11.5米，選配不同規格的鉆具，樁孔直接范圍可達直徑200-1200mm，施工完畢將鉆桿收復歸位后，可以每小時0-30公里的速度快速轉場，機動靈活，便捷高效，是國家高鐵建設專用的樁工機械設備。

Spiral drill the pressurized drilling work mode, can realize the rotary digging pile deep 2.5 meters, 5.5 meters, 2.5 meters, equipped with different specifications of the drill, the pile hole directly range can reach 200-1200 - mm diameter, finished, recovered after place, will drill pipe can be 0 to 30 km per hour speed quick turnarounds, flexible, convenient and efficient, is the country dedicated high-speed rail construction pile driving machinery equipment.

適用于土層、黏土層、填土層、粘土層、粉土層、淤泥層、沙土層及部分含有卵石的地層，適用于高鐵接觸網支架樁、護坡樁，太陽能光伏電站地基支架樁，電網改造、民用建筑、新農村建設、市政工程建設、園林綠化等多種工程項目。

Applied to the soil, clay layer, fill soil, clay, powder soil and silt layer, sand layer and part includes the pebble stratum, is suitable for the high-speed catenary stent pile, slope protection, solar photovoltaic power station pile foundation support, network reconstruction, civil construction, construction of new countryside construction, municipal engineering, landscaping and other projects.

機動靈活：整機噸位小，操作簡單，移動快速，轉場便利，具有一個樁孔也能打的特點。

Flexible: the machine tonnage small, simple operation, move fast, convenient transitions, have the characteristics of a pile hole can also be played.

螺旋鉆機安全操作規程

1、司機必須經培訓合格后，方可上機操作，所有工作人員應穿絕緣鞋，戴安全帽。

2、應配正副司機各一人，司機酒后或患病不得上機操作。

3、司機必須進行設備的日常維護保養，對機械狀況認真填寫記錄。

4、工作前應檢查電機及其它電器絕緣情況，發現問題隨即處理。

5、樁機施工現場應在離開高壓電線(纜)、油氣管道的有關規定危險距離以外工作。

6、起落立柱應有專人指揮與操作，支腳與履靴應同時接地，前支腿伸于前方，立柱、斜撐下嚴禁站人。

7、樁機移位時應有專人指揮，并安排人員移動電源線以防碰壓。支腳下松軟時應用枕木等輔墊以保證接地比壓。

8、樁機移動、回轉時嚴禁用上盤、履靴頂土或排除障礙物。特別提示：鉆機、回轉時移動前應及時清土、清障處理；支腿支起否則極易發生鉆機損壞事故，影響正常施工。

9、施工現場不平度應小于2°，地面承載力不小于100kPa。

10、鉆孔時注意調整立柱垂直度，并應使支腳與履靴同時接地。

11、本機在六級以下風力工作。在大風雨雪天氣應停止施工，且在大風時應加纜繩予以保護。

12、施工中若樁機回轉支路頻繁自動停止，其一應檢查電機綜合保護器電流刻度調節值是否合適，其二應及時排除樁機回轉過程中的障礙。

Spiral drill safety operation procedures
1, the driver must be qualified after the training, can use the computer operation, all the staff should wear insulated shoes, wearing a helmet.
2, the driver should be under each one, "the driver drunk or sick computer operation is not allowed.
3, the driver must conduct equipment daily maintenance, fill in record for mechanical condition.
4, before work should check the motor and other electric insulation, found the problem immediately.
5, pile machine construction site shall be left high-voltage wire (cable), the relevant provisions of the oil and gas pipeline risk distance work.
6, ups and downs column should be the specialist command and operation, the leg and the shoe boots should ground at the same time, the front leg stretched out in front, columns, it is forbidden to stand under brace.
7, pile machine shift personnel command, and arrange personnel to move the power cord to prevent bruising.When the feet soft sleeper applications auxiliary pad to ensure the ground pressure.
8, pile machine movement, it is forbidden to use when turning plate, the shoe boots top soil or eliminate obstacles.Special note: when the drill, rotary movement should be timely clean soil, repair processing before,Drill leg up otherwise easily happened damage accidents, affect the normal construction.
9, the roughness should be less than 2 ° to the construction site and the ground bearing capacity not less than 100 kpa.
10, drilling, pay attention to adjusting column vertical degree, and should make the leg and the shoe boots ground at the same time.
11, the machine work under 6 wind.In wind rain and snow weather should stop construction, and should add the cable protected when strong winds.

12, If, during the construction of the pile machine rotary branch automatically stop frequently, one should check the motor synthetical protector current scale adjustment value is appropriate, the other should be promptly eliminate the obstacles in the process of turning machine.

高額回報：投資小，收益快，經濟優勢不可代替。

High returns: small investment, fast gains for economic advantage.

濟寧恒旺工礦機械專注機械十年，全國聯保，值得您的信賴